| Aadhunik Industries is a manufacturing group company. Aadhunik Industries is pioneer manufacturers of Flow Back Aid, Surfactant, Specialty Chemicals, Pharmaceutical Excipients, Food Fragrance & Flavor chemicals in India. It has toll manufacturers and representatives in UAE, Europe, Canada & USA and agents & customers in all countries like USA, Canada, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Dubai, Netherlands, Italy, Spain, Germany, Portugal, France, Malaysia, Indonesia, Thailand, Korea, Japan, Russia etc. Our services are 24/7 deliveries, including week-end deliveries, wellsite logistics in ISO tanks, logistics & warehousing across the world, sourcing from overseas, manufacturing overseas, quality control, GHS compliance, etc. |
| Aadhunik Industries and/or associated units are FDA-cGMP certified, Halal and/or Kosher certified, REACH registered, ISO-9001, ISO-22000 HACCP certified. We offer crystals granules in precise micron or mesh size as per buyers needs. We supply very high purity standards as per specifications required. |
---------- 
---------- 
Translate
Flow Back Aid, Surfactant Manufacturers Exporters
SDS, MSDS of Flow Back Aid, Surfactant Manufacturers
Surfactant S-112, Water Recovery Surfactant (FlowBack Aid)
Use:
S-112 is a proprietary non-ionic, non-flammable surfactant for use in acidizing and fracturing treatments. It is designed to improve recovery of the injected stimulation fluids and enhance ultimate recovery of hydrocarbons.
S-112 effectively lowers interfacial tension between stimulation fluids and hydrocarbons. It lowers the capillary pressure and allows for greater penetration in to the formation face, therefore promoting the recovery of stimulation fluids, connate fluids and hydrocarbons.
S-112 is compatible with all known fracturing fluid additives and has been successfully used in West Texas, South Texas, East Texas and Oklahoma for the past few years. S-112 is also pumped with acid spearheads to lower the breakdown pressures and minimize the possibilities of forming acid/oil emulsions where a separate non-emulsifier is not used.
Physical & Chemical Properties:
Appearance: Clear, Straw Yellow Liquid
Odor: Faint Organic
Density: 8.4 lbs/ga
Pour Point: Less than 20 deg F
Flash Point: Greater than 175 deg F
Typical Surface Tension: Less than 30 dynes/cm2
Typical Interfacial Tension: Less than 3 mN/m
Wetting Characteristic: Water Wetting
Compatibility: S-112 is compatible with most acidizing and fracturing treatment additives and friction reducers. However, a compatibility test is advised before use.
Environment: Not hazardous to the environment.
Typical Dosage: Typically used at 1 to 2 GPT with stimulation fluids
Temperature Limitations: Can be used across a wide temperature range, no lower temperature limitation on performance. Has been effectively used up to BHT of 350 F.
Packaging: 330 ga one way totes, 275 ga one way totes, 55 ga drums and bulk tank trucks.
Flow Back Aid, Surfactant manufacturers exporters at:
Aadhunik Industries
Ankleshwar Gujarat & Mumbai, India
TEL: (OFFICE) 91-22-23774610, 23723564.
e-mail: info@aadhunikindustries.com
Copyright and Usual Disclaimer is Applicable.
6-06-2022
Hazards statements come here.
DISCLAIMER: The information and recommendations set forth herein (hereinafter "Information") are presented in good faith and believed correct as of the date hereof. It is compiled from various sources and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules or insurance requirements applicable. This SDS MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose.
Hydraulic Fracturing Chemicals