Tin fluoride or Stannous Fluoride USP Grade Manufacturers Exporters |
| Aadhunik Industries is a manufacturing group company. Aadhunik Industries is pioneer manufacturers of Tin fluoride or Stannous Fluoride, Specialty Chemicals, Pharmaceutical Excipients, Food Fragrance & Flavor chemicals in India. It has toll manufacturers and representatives in UAE, Europe, Canada & USA and agents & customers in all countries like USA, Canada, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Dubai, Netherlands, Italy, Spain, Germany, Portugal, France, Malaysia, Indonesia, Thailand, Korea, Japan, Russia etc. |
| Aadhunik Industries and/or associated units are FDA-GMP certified, Halal and/or Kosher certified, REACH registered, ISO-9001, ISO-22000 HACCP certified. We offer crystals granules in precise micron or mesh size as per buyers needs. We offer very high purity standards as per specifications required. |
---------- 
---------- 
Translate
SDS MSDS of Tin fluoride or Stannous Fluoride Manufacturers
Specifications of Stannous Fluoride USP Grade
SnF2 -- 156.71
Tin fluoride (SnF2) [CAS 7783-47-3].
Stannous Fluoride contains not less than 71.2 percent of stannous tin (Sn ++), and not less than 22.3 percent and not more than 25.5 percent of fluoride (F), calculated on the dried basis.
Identification:
A: To 5 mL of a solution (1 in 100) in a test tube add 2 mL of calcium chloride TS: a fine, white precipitate of calcium fluoride is formed.
B: Mix on a spot plate 2 drops of a solution (1 in 100) with 2 drops of silver nitrate TS: a brown-black precipitate is formed.
C: Add 1 drop of a solution (1 in 100) to 2 drops of mercuric chloride: a white, silky precipitate is formed. On further addition of the solution (1 in 100), a brown-black precipitate is formed.
pH: between 2.8 and 3.5, in a freshly prepared 0.4% solution.
Loss on drying: Dry it at 105C for 4 hours: it loses not more than 0.5% of its weight.
Water-insoluble substances: Transfer about 10 g, accurately weighed, to a 400-mL plastic beaker, add 200 mL of water, and stir with a plastic rod for 3 minutes, or until no more solid dissolves. Filter through a tared filtering crucible, and wash thoroughly, first with ammonium fluoride solution (1 in 100), then with water. [NOTE—Prepare and use the filtering crucible in a well-ventilated hood.] Dry the residue at 105C for 4 hours, cool, and weigh: the weight of the residue does not exceed 0.2%.
Antimony:
Rhodamine B solution: Dissolve 20 mg of rhodamine B in 200 mL of 0.5 N hydrochloric acid.
Standard preparation: Transfer 55.0 mg of antimony potassium tartrate, accurately weighed, to a 200-mL volumetric flask, dissolve in water, dilute with water to volume, and mix. Transfer 5.0 mL of this solution to a 500-mL volumetric flask, add 6 N hydrochloric acid to volume, and mix.
Test preparation: Transfer 1.0 g of Stannous Fluoride, accurately weighed, to a 50-mL volumetric flask, add 6 N hydrochloric acid to volume, and mix.
Procedure: Pipet 5 mL each of the Standard preparation and the Test preparation into separate 125-mL separators, add 15 mL of hydrochloric acid and 1 g of ceric sulfate, and allow to stand for 5 minutes, with occasional shaking. Add 500 mg of hydroxylamine hydrochloride, and shake for 1 minute. Pipet 15 mL of isopropyl ether into the mixture, shake for 30 seconds, add 7 mL of water, and mix. Cool in a water bath at room temperature for 10 minutes, shake for 30 seconds, allow the layers to separate, and discard the aqueous phase. Add 20 mL of Rhodamine B solution, shake for 30 seconds, and discard the aqueous layer. Decant the ether layer from the top of the separator, and centrifuge, if necessary, to obtain a clear solution. Concomitantly determine the absorbances of the ether solutions from the Test preparation and the Standard preparation at the wavelength of maximum absorbance at about 550 nm, with a suitable spectrophotometer, using water as the blank: the absorbance of the Test preparation does not exceed that of the Standard preparation (0.005%).
CAS Number 7783-47-3, Tin fluoride or Stannous Fluoride manufacturers suppliers exporters at:
manufacturer supplier exporter
Aadhunik Industries
Ankleshwar Gujarat & Mumbai, India
TEL: (OFFICE) 91-22-23774610, 23723564.
e-mail: info@aadhunikindustries.com
Copyright and Usual Disclaimer is Applicable. 10-12-2022
Acetic Acid Glacial ------- Ammonium Bicarbonate ------- Aluminum Chloride ------- Aluminium Potassium Sulphate ------- Ammonium Carbonate ------- Ammonium Carbamate ------- Ammonium Chloride ------- Ammonium Persulfate------- Barium Chloride ------- Benzyl Alcohol ------- Benzoic Acid ------- Boric Acid ------- Borax ------- Calcium Chloride ------- Calcium Oxide ------- Calcium Hydroxide ------- Calcium Lactobionate ------- Calcium D Saccharate ------- Calcium Sulfate ------- Carbamide Peroxide ------- Chromic Chloride -------Copper Cupric Chloride ------- Copper Sulphate ------- Precipitated Coated & Directly Compressible Calcium Carbonate ------- Fumaric Acid ------- Ferric Chloride ------- Formaldehyde Solution ------- Lithium Carbonate ------- Magnesium Chloride ------- Magnesium Sulphate ------- Maleic Acid ------- Malic Acid ------- Manganese Chloride ------- Manganese Sulphate ------- Octyl Dodecanol ------- Oleic Acid ------- Phenyl Ethanol ------- Potassium Bromide ------- Potassium Chloride ------- Potassium Hydroxide Pellets ------- Potassium Monopersulfate ------- Potassium Phosphate Monobasic Dibasic Tribasic ------- Propylene Carbonate ------- Selenious Acid ------- Sodium Acetate ------- Sodium Diacetate ------- Sodium Hydroxide Pellets------- Sodium Thiosulfate ------- Sodium Formaldehyde Bisulfite ------- Sodium Perborate ------- Vanadyl Sulfate ------- Zinc Chloride