Chromium Chloride, Chromic Chloride Manufacturers Exporters

Aadhunik Industries is a manufacturing group company. Aadhunik Industries is pioneer manufacturers of Chromium Chloride, Chromic Chloride, Specialty Chemicals, Pharmaceutical Excipients, Food Fragrance & Flavor chemicals in India. It has toll manufacturers and representatives in UAE, Europe, Canada & USA and agents & customers in all countries like USA, Canada, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Dubai, Netherlands, Italy, Spain, Germany, Portugal, France, Malaysia, Indonesia, Thailand, Korea, Japan, Russia etc.

Aadhunik Industries and/or associated units are FDA-GMP certified, Halal and/or Kosher certified, REACH registered, ISO-9001, ISO-22000 HACCP certified. We offer crystals granules in precise micron or mesh size as per buyers needs. We offer very high purity standards as per specifications required.

Chromic Chloride or Chromium Chloride contains not less than 98.0 percent and not more than 101.0 percent of CrCl3·6H2O.
Insoluble matter—0.01%).
Substances not precipitated by ammonium hydroxide— (0.20% as sulfate).
Sulfate— (0.01%).
Iron— The limit is 0.01%.

Chromic Chloride USP Chromium Chloride
CrCl3-6H2O -- 266.45
Chromium chloride (CrCl3) hexahydrate
Chromium(3+) chloride hexahydrate [CAS 10060-12-5]
Anhydrous 158.36 [CAS 10025-73-7]

Chromium Chloride - Chromic Chloride or Chromium Chloride contains not less than 98.0 percent and not more than 101.0 percent of CrCl3-6H2O

Identification:
A: To 5 mL of a solution (1 in 250) in a test tube add 1 mL of 5 N sodium hydroxide and 10 drops of 30 percent hydrogen peroxide, and heat gently for about 2 minutes: a yellow color develops.
B: To 5 mL of a solution (1 in 250) in a test tube add 5 drops of silver nitrate TS: a white, curd like precipitate is formed, and it is insoluble in nitric acid.
Insoluble matter: Transfer 10 g to a 250-mL beaker, add 100 mL of water, cover the beaker, and heat to boiling. Digest the hot solution on a steam bath for 30 minutes, and filter through a tarred filtering crucible of fine porosity. Rinse the beaker with hot water, passing the rinsing through the filter, and wash the filter with hot water until the last washing is colorless. Dry the filter at 105C the weight of the residue does not exceed 1 mg (0.01%).
Substances not precipitated by ammonium hydroxide: Dissolve 2.0 g of Chromic Chloride or Chromium Chloride in 80 mL of water, heat the solution to boiling, and add a slight excess of ammonium hydroxide. Continue heating to remove the excess ammonia, cool, dilute with water to 100.0 mL, and mix. Pass through a retentive filter, and transfer 50.0 mL of the clear filtrate to an evaporating dish that previously has been ignited and tarred. Add 0.5 mL of sulfuric acid to the filtrate, evaporate on a steam bath to dryness, heat gently to remove the excess acid, and ignite gently: the weight of the residue does not exceed 2.0 mg (0.20% as sulfate).
Sulfate: Prepare a test solution by dissolving 2.0 g in 10 mL of water. Add 1 mL of 3 N hydrochloric acid, filter if necessary to obtain a clear solution, wash the filter with two 5-mL portions of water, and dilute with water to 40 mL. Prepare a control solution in a similar manner, but use 1.0 g of the substance under test, and after the filtration step add 0.10 mL of 0.020 N sulfuric acid. To each solution add 3 mL of barium chloride TS, mix, and allow to stand overnight. Decant most of the supernatants, without disturbing the precipitates, but leaving twice the volume of liquid in the control solution as in the test solution. Dilute each solution with water to 25 mL, and sonicate for 1 minute: any turbidity in the test solution does not exceed that in the control solution (0.01%).
Iron: Dissolve 1.0 g of Chromic Chloride or Chromium Chloride in 100 mL of water, and mix. Transfer 10 mL of this solution to a 100-mL color comparison tube, dilute with water to 45 mL, add 2 mL of hydrochloric acid, and mix (Test Preparation). Proceed as directed for Procedure, except to add 15 mL of butyl alcohol to the Test Preparation and the Standard Preparation at the same time that the Ammonium Thiocyanate Solution is added. Shake for 30 seconds, and allow the layers to separate: the color in the upper butyl alcohol layer from the Test Preparation is not darker than that from the Standard Preparation. The limit is 0.01%.

CAS Number 10060-12-5, Chromium Chloride Chromic Chloride Commercial Pure & USP manufacturers suppliers exporters at:

manufacturer supplier exporter
Aadhunik Industries
Ankleshwar Gujarat & Mumbai, India
TEL: (OFFICE) 91-22-23774610, 23723564.