Ferric oxide USP NF Grade Manufacturers Exporters |
| Aadhunik Industries is a manufacturing group company. Aadhunik Industries is pioneer manufacturers of Ferric oxide, Specialty Chemicals, Pharmaceutical Excipients, Food Fragrance & Flavor chemicals in India. It has toll manufacturers and representatives in UAE, Europe, Canada & USA and agents & customers in all countries like USA, Canada, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Dubai, Netherlands, Italy, Spain, Germany, Portugal, France, Malaysia, Indonesia, Thailand, Korea, Japan, Russia etc. |
| Aadhunik Industries and/or associated units are FDA-GMP certified, Halal and/or Kosher certified, REACH registered, ISO-9001, ISO-22000 HACCP certified. We offer crystals granules in precise micron or mesh size as per buyers needs. We offer very high purity standards as per specifications required. |
---------- 
---------- 
Translate
SDS MSDS of Ferric oxide Manufacturers
Iron(III) oxide or ferric oxide is the inorganic compound with the formula Fe2O3. It is one of the three main oxides of iron, the other two being iron(II) oxide (FeO), which is rare, and iron(II,III) oxide (Fe3O4), which also occurs naturally as the mineral magnetite.
Ferric Oxide USP NF
Ferric Oxide contains not less than 97.0 percent and not more than 100.5 percent of Fe2O3, calculated on the ignited basis.
Packaging and storage: Preserve in well-closed containers.
Identification: Dissolve 0.5 g in 50 mL of hydrochloric acid, and dilute with water to 200 mL: the solution so obtained responds to the test for Ferric Salts under Iron..
Water-soluble substances: Digest 2.0 g in 100 mL of water on a boiling water bath for 2 hours, filter, and wash the filter with water. Evaporate the filtrate and washings, and dry the residue at 105 for 1 hour: the weight of the dried residue is not more than 20 mg (1.0%).
Acid-insoluble substances: Digest 2.0 g in 25 mL of hydrochloric acid by boiling for 20 minutes. Add 100 mL of hot water, and filter quantitatively through a tared filtering crucible, with the aid of hot wash water, until the filtrate tests negative for chloride. Dry the crucible and contents at 105 for 1 hour: the residue weighs not more than 6 mg (0.3%).
Organic colors and lakes: Place 1.0 g in each of 3 beakers, and add 25 mL of each of the following reagents, respectively: 1-chloronaphthalene, alcohol, and chloroform. Heat the beakers containing alcohol and chloroform just to boiling. Heat the other beaker on a boiling water bath for 15 minutes, with occasional swirling. Filter the contents of the beakers through retentive, solvent-resistant filter paper. If any of the filtrates shows visible turbidity, centrifuge for 15 minutes. Record the spectra against respective solvent blanks in 1-cm cells from 350 to 750 nm. No peak, above the noise level, with a slope greater than +0.001 absorbance unit per nm is found.
Mercury: The limit is 3 µg per g.
Limit of arsenic: The limit is 3 µg per g.
Limit of lead: The limit is 0.001%. (0.001%).
Assay: Digest about 1.5 g of Ferric Oxide, accurately weighed, in 25 mL of hydrochloric acid on a water bath until dissolved. Add 10 mL of hydrogen peroxide and evaporate on a water bath almost to dryness in order to volatilize all hydrogen peroxide. Dissolve the residue by warming with 5 mL of hydrochloric acid; add 25 mL of water; filter into a 250-mL volumetric flask, washing the filter with water; and add water to volume. Transfer a 50-mL aliquot to a glass-stoppered flask, add 3 g of potassium iodide and 5 mL of hydrochloric acid, and insert the stopper into the flask. Allow the mixture to stand for 15 minutes, add 50 mL of water, and titrate the liberated iodine with 0.1 N sodium thiosulfate, using starch as the indicator. Perform a blank test with the same quantities of reagents and in the same manner, and make any necessary corrections. Each mL of 0.1 N sodium thiosulfate is equivalent to 7.985 mg of Fe2O3. Ignite about 2 g of Ferric Oxide at 800 ± 25 to constant weight as directed under Loss on Ignition 733 , to enable calculation of the percentage of Fe2O3 on the ignited basis. [NOTE—Ignited Ferric Oxide is hygroscopic.]
CAS Number 1309-37-1, Ferric oxide USP NF Grade manufacturers suppliers exporters at:
manufacturer supplier exporter
Aadhunik Industries
Ankleshwar Gujarat & Mumbai, India
TEL: (OFFICE) 91-22-23774610, 23723564.
e-mail: info@aadhunikindustries.com
Copyright and Usual Disclaimer is Applicable. 6-12-2022
Ammonium Bromide ------- Aluminum Chloride ------- Aluminium Potassium Sulphate ------- Ammonium Chloride ------- Ammonium Persulfate------- Ammonium Phosphate Monobasic or Dibasic or Monoammonium Diammonium Phosphate ------- Barium Chloride ------- Benzyl Alcohol ------- Benzoic Acid ------- Boric Acid ------- Borax ------- Calcium Chloride ------- Calcium Oxide ------- Calcium Hydroxide ------- Calcium D Saccharate ------- Calcium Sulfate ------- Chromic Chloride ------- Citric Acid ------- Cobalt Chloride ------- Copper Cupric Chloride ------- Copper Sulphate ------- Cuprous Chloride ------- Precipitated Coated & Directly Compressible Calcium Carbonate ------- Fumaric Acid ------- Ferric Chloride ------- HEDP ------- Isatoic Anhydride ------- Magnesium Chloride ------- Magnesium Sulphate ------- Maleic Acid ------- Malic Acid ------- Manganese Chloride ------- Manganese Sulphate ------- Phenyl Ethanol ------- Potassium Bromide ------- Potassium Bicarbonate ------- Potassium Carbonate ------- Potassium Chloride ------- Potassium Hydroxide Pellets ------- Potassium Phosphate Monobasic Dibasic Tribasic ------- Propylene Carbonate ------- Sodium Acetate ------- Sodium Diacetate ------- Sodium Hydroxide Pellets ------- Sodium Propionate ------- Sodium Thiosulfate ------- Sodium Formaldehyde Bisulfite ------- Sodium Phosphate Monobasic Dibasic Tribasic ------- Sodium Perborate ------- Sulfamic Acid ------- Tetra-basic zinc hydroxychloride -------- Urea Industrial Grade ------- Zinc Chloride